Home - Current Owners - Nissan Recalls - 1994

Most Recent 1994 Nissan Recalls

According to the NHTSA approximately 42,000 lives are lost annualy on our Nation's highways. Nissan does it's part to try to reduce this number by voluntarily iniating recalls on 1994 Nissan products. If a safety defect is discovered, Nissan must notify NHTSA, as well as vehicle or equipment owners, dealers, and distributors. Nissan is required to remedy the problem (Nissan recall) at no charge to the Nissan owner.

If you would like to check on any 1994 Nissan Recall Notices for your vehicle, please enter the appropriate year and model.


Year *	Make *	Model *

1994 isuzu Recalls




	NHTSA CAMPAIGN ID Number: 06E065000 Component: EXTERIOR LIGHTING Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 3593 Year: 1994 Make: Isuzu Model: Rodeo Manufactured from: 0000-00-00 to: 0000-00-00 Recall Date: 2006-07-17 Summary: CERTAIN AJ MOTORSPORT COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH. AJ MOTORSPORT WILL NOTIFY OWNERS AND OFFER REIMBURSEMENT FOR THE LAMPS. THE RECALL BEGAN ON JULY 31, 2006. OWNERS MAY CONTACT AJ MOTORSPORT AT 626-618-2026.




	NHTSA CAMPAIGN ID Number: 06E026000 Component: EXTERIOR LIGHTING Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 61944 Year: 1994 Make: Isuzu Model: Pickup Truck Manufactured from: 0000-00-00 to: 0000-00-00 Recall Date: 2006-03-23 Summary: CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. WITHOUT THE AMBER REFLECTORS, THE VEHICLE WILL BE POORLY ILLUMINATED, POSSIBLY RESULTING IN A VEHICLE CRASH WITHOUT WARNING. PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.




	NHTSA CAMPAIGN ID Number: 04V199000 Component: VEHICLE SPEED CONTROL:CABLES Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 72905 Year: 1994 Make: Isuzu Model: Trooper Manufactured from: 1993-05-01 to: 1994-11-30 Recall Date: 2004-04-22 Summary: ON CERTAIN SPORT UTILITY VEHICLES, THE ACCELERATOR CABLE CAN STICK SO THAT THE ENGINE SPEED WILL NOT IMMEDIATELY DECREASE UPON RELEASE OF THE ACCELERATOR PEDAL. THIS CAN CAUSE THE ACCELERATOR THROTTLE CABLE TO DELAY RPM AND VEHICLE SPEED REDUCTION FOR SEVERAL SECONDS AFTER THE ACCELERATOR PEDAL IS RELEASED, WHICH IN TURN, CAN LEAD TO A CRASH. DEALERS WILL REPLACE THE THROTTLE CABLE RUBBER BOOT. OWNER NOTIFICATION BEGAN ON MAY 24, 2004. OWNERS SHOULD CONTACT ISUZU AT 1-800-255-6727.




	NHTSA CAMPAIGN ID Number: 02V281000 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 14449 Year: 1994 Make: Isuzu Model: Rodeo Manufactured from: 1994-01-01 to: 1994-07-31 Recall Date: 2002-10-15 Summary: ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS, THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MID-DECEMBER 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT ISUZU AT 1-800-643-4070.




	NHTSA CAMPAIGN ID Number: 02V281000 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 14449 Year: 1994 Make: Isuzu Model: Tf Manufactured from: 1994-04-01 to: 1994-08-31 Recall Date: 2002-10-15 Summary: ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS, THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MID-DECEMBER 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT ISUZU AT 1-800-643-4070.




	NHTSA CAMPAIGN ID Number: 02V281000 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 14449 Year: 1994 Make: Isuzu Model: Amigo Manufactured from: 1993-11-01 to: 1994-02-28 Recall Date: 2002-10-15 Summary: ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS, THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MID-DECEMBER 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT ISUZU AT 1-800-643-4070.




	NHTSA CAMPAIGN ID Number: 02V281000 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 14449 Year: 1994 Make: Isuzu Model: Pickup Truck Manufactured from: 1994-04-01 to: 1994-08-31 Recall Date: 2002-10-15 Summary: ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS, THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MID-DECEMBER 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT ISUZU AT 1-800-643-4070.




	NHTSA CAMPAIGN ID Number: 97V034001 Component: ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 118485 Year: 1994 Make: Isuzu Model: Rodeo Manufactured from: 1994-07-01 to: 1994-10-31 Recall Date: 1997-03-07 Summary: AN INTEGRATED CIRCUIT WITHIN THE VOLTAGE REGULATOR CAN CONTAIN MANUFACTURING ERRORS. THIS CAN CAUSE EXCESSIVE ELECTRICAL CHARGING OF THE VEHICLE'S ALTERNATOR, RESULTING IN ENGINE CONTROL MALFUNCTION, AND/OR EVENTUAL ENGINE STALL. DEALERS WILL REPLACE THE VOLTAGE REGULATOR WITH A NEW REGULATOR.




	NHTSA CAMPAIGN ID Number: 96V170002 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 36075 Year: 1994 Make: Isuzu Model: Rodeo Manufactured from: 1994-01-01 to: 1994-07-31 Recall Date: 1996-09-17 Summary: THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE.




	NHTSA CAMPAIGN ID Number: 96V170002 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 36075 Year: 1994 Make: Isuzu Model: Pickup Truck Manufactured from: 1994-01-01 to: 1994-07-31 Recall Date: 1996-09-17 Summary: THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE.




	NHTSA CAMPAIGN ID Number: 96V170002 Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 36075 Year: 1994 Make: Isuzu Model: Amigo Manufactured from: 1993-11-01 to: 1993-12-31 Recall Date: 1996-09-17 Summary: THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT. THIS CONDITION CAN CAUSE THE SEAT BELT TONGUE TO COME OUT OF THE BUCKLE IN THE EVENT OF A COLLISION OR HARD BRAKING OF THE VEHICLE INCREASING THE RISK OF PERSONAL INJURY TO AN OCCUPANT OF THE SEAT. DEALERS WILL INSPECT THE BUCKLE AND, IF NECESSARY, REPLACE THE BUCKLE ASSEMBLY WITH A NEW BUCKLE.




	NHTSA CAMPAIGN ID Number: 94V132000 Component: ENGINE AND ENGINE COOLING:ENGINE Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 122297 Year: 1994 Make: Isuzu Model: Rodeo Manufactured from: 1991-11-01 to: 1994-04-01 Recall Date: 1994-07-19 Summary: CONSTANT EXPANSION AND CONTRACTION OF THE CYLINDER HEAD CAUSES THE CAMSHAFT SEAL END PLUG CAN BECOME DISLODGED FROM THE CYLINDER HEAD. THIS ALLOWS OIL TO LEAK FROM THE CAMSHAFT. THIS CAN CAUSE ENGINE DAMAGE AND POSSIBLE ENGINE FIRE FROM OIL LEAKING ONTO THE HOT EXHAUST SYSTEM. DEALERS WILL INSTALL CAMSHAFT END SEAL PLUG RETAINER PLATES.




	NHTSA CAMPAIGN ID Number: 94V132000 Component: ENGINE AND ENGINE COOLING:ENGINE Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 122297 Year: 1994 Make: Isuzu Model: Trooper Manufactured from: 1991-11-01 to: 1994-04-01 Recall Date: 1994-07-19 Summary: CONSTANT EXPANSION AND CONTRACTION OF THE CYLINDER HEAD CAUSES THE CAMSHAFT SEAL END PLUG CAN BECOME DISLODGED FROM THE CYLINDER HEAD. THIS ALLOWS OIL TO LEAK FROM THE CAMSHAFT. THIS CAN CAUSE ENGINE DAMAGE AND POSSIBLE ENGINE FIRE FROM OIL LEAKING ONTO THE HOT EXHAUST SYSTEM. DEALERS WILL INSTALL CAMSHAFT END SEAL PLUG RETAINER PLATES.




	NHTSA CAMPAIGN ID Number: 94V085000 Component: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS Manufacturer: ISUZU MANUFACTURING SERVICES OF AMERICA Potential Number of Units Affected: 130 Year: 1994 Make: Isuzu Model: Npr Manufactured from: 1993-11-01 to: 1994-03-01 Recall Date: 1994-05-03 Summary: ON SOME VEHICLES, THE SEALING SURFACES FOR A HYDRAULIC BRAKE HOSE ON A FRONT BRAKE CALIPER WERE COVERED BY PAINT RESIDUE. BRAKE FLUID GRADUALLY DISSOLVES THE PAINT, OPENING A SMALL PATH BETWEEN THE SEALING SURFACE AND THE GASKET ALLOWING BRAKE FLUID TO LEAK WHEN THE BRAKE IS APPLIED. THIS CAN RESULT IN INCREASED STOPPING DISTANCES AND A POSSIBLE VEHICLE ACCIDENT. DEALERS WILL REMOVE PAINT FROM THE BRAKE CALIPER, REPLACE COPPER GASKETS AND BLEED THE FRONT BRAKES.